Words of advice....DON'T FORGET THE DOWEL PINS WHEN YOU PUT THE HEAD ON AND TORQUE IT DOWN!!!
Green Bullet ST205 Re-Born - 6G Celicas Forums
love the valve cover man!
st205 powered ss3 coupe
The secret to the valve cover revealed...
Then
Then
Lots of attention to detail here. Keep up the good work.
Picked up these bad boys for 15 bucks a piece. STEAL!!!
This post has been edited by bsamps4: Nov 22, 2011 - 6:48 PM
This post has been edited by bsamps4: Nov 22, 2011 - 6:48 PM
what is that an engine mount? bearing? timing belt pulley?
What I think when you think I care
idler bearings
Toyota would like 52$ a piece for these.
Toyota would like 52$ a piece for these.
After all the issues I've had with dowel pins, and installing the head gasket....I've finally had a bit of success...
Dowel Pins In.
Done.
Dowel Pins In.
Done.
All anyone ever needs: red, silver, and black, and some engine in between.
This post has been edited by SwissFerdi: Nov 30, 2011 - 5:31 PM
This post has been edited by SwissFerdi: Nov 30, 2011 - 5:31 PM
'97 ST\ Eibach \ KYB \ Kenwood \ Alpine \ Cusco \ OEM+[sold 10/18]'93 MX-5LE
freakin sweeet
Power in Balance90 ST coupe- Sold95 ST hatch- Dead :(02 Impreza RS- DD
"Is that for me?" - car in background lol
What I think when you think I care
Lol this reminds me so much of my car/engine build. granted i didnt tear as far into the engine as you but just damn!
1996 Toyota Celica Project Mean Green3RD Gen 3SGTE WRC Edition W/LSD E153 - Love BOOST <32001 Solar yellow Lexus IS3002001 Dodge ram 1500 Off-road edition
builds lookin sweet! motor looks cleann
st205 powered ss3 coupe
Thanks for all the kind words guys. Hope to have her running soon!
>
LOL
>
QUOTE (Neon90424 @ Dec 1, 2011 - 10:37 AM) 
>
"Is that for me?" - car in background lol
"Is that for me?" - car in background lol
LOL
oh sexy engine dress up!
Group buy to replicate Narrow E series transaxle partshttp://www.6gc.net/forums/index.php?showto...p;#entry1107514
that engine looks damn good. Makes me wish I had time to work on mine
The block on the stand is pure sex. Perfection...now I have to think up another theme =P
I might paint my wheels with your formula man!
What I think when you think I care
It's a pretty cool color. My wheels are sporting the same finish. I will snag a pic for ya.
That enamel works great, I've had my wheels that way for about half a year now, and it doesn't chip, not from heat at least. Goes on nicely as well.
'97 ST\ Eibach \ KYB \ Kenwood \ Alpine \ Cusco \ OEM+[sold 10/18]'93 MX-5LE
>
thanks bud much obliged
QUOTE (bsamps4 @ Dec 3, 2011 - 9:41 AM)
>It's a pretty cool color. My wheels are sporting the same finish. I will snag a pic for ya.
thanks bud much obliged
What I think when you think I care
Hi,
does i ask you, can you give me the diameter measurement of
IDLER SUB-ASSY, TIMING BELT, NO.1
http://www.toyodiy.com/parts/p_E_1995_TOYO...LMVZW_1302.html
the issue i had is that i want to use the smaller gen.3 oil pump gear on my gen.4, i bought both idlers from gen.4 but now i saw that gen.3 had different part numbers
and i doesnt want to get problems with timing belt tension
the gen.4 one has the following measurment
here are my measurements
60 x 29,6mm
i'am glad if you can help me
greetz
This post has been edited by Sunny: Dec 4, 2011 - 6:12 AM
does i ask you, can you give me the diameter measurement of
IDLER SUB-ASSY, TIMING BELT, NO.1
http://www.toyodiy.com/parts/p_E_1995_TOYO...LMVZW_1302.html
the issue i had is that i want to use the smaller gen.3 oil pump gear on my gen.4, i bought both idlers from gen.4 but now i saw that gen.3 had different part numbers
and i doesnt want to get problems with timing belt tension
the gen.4 one has the following measurment
here are my measurements
60 x 29,6mm
i'am glad if you can help me
greetz
This post has been edited by Sunny: Dec 4, 2011 - 6:12 AM
KEEP COOL UNDER PRESSURE
The outer diameter is 57.15mm and the width is 28.57mm on the bearing.
Hi,
thanks a lot
greetz
thanks a lot
greetz
KEEP COOL UNDER PRESSURE
Spent all day installing the fog lights that I bought from Block. Since I don't have a JDM crash bar or frame rail adapters, I had to modify the factory crash bar. I had to drill and bolt the JDM fog lights, and use 1/4 inch spacers to get the fitment lined up. Also had to modify the fog light mounting brackets so that everything would come together nicely. Since I don't have a sunroof I used the blank in the dash as a mounting location for my switch. I drilled out the blank with a 3/4" drill bit and screwed the new switch in. Looks factory! Hope you guys enjoy the pics.
Also have a test fit intercooler teaser.
Intercooler Test Fit
Fog Light Test Fit
Fog Lights Installed and Working
Fog lights with HID's and running lights on.
Also have a test fit intercooler teaser.
Intercooler Test Fit
Fog Light Test Fit
Fog Lights Installed and Working
Fog lights with HID's and running lights on.
giggity!
What I think when you think I care
Simply illuminating!
Sorry...I had to.
Sorry...I had to.
Has no more Celicas
I'm glad it's working out for you bro. SICK car! Lovin' the huge intercooler man!
Haha I love the Hugh Jass intercooler too, but I'm worried that it's not going to fit with the fogs. May end up having to sell it, and get a smaller one, but i'll see what I can do.
how much HP is that intercooler rated for?
What I think when you think I care