Suspension/Handling/Braking

5,114 Total Topics
25 Showing
71 Page 71 of 205
Topics in Suspension/Handling/Braking • newest topics first
2 posts • Started by Promasta
Kumho Ecsta AST at tirerack $66 each...
15 posts • Started by 97celiman
aha! i knew i wasn't crazy http://www.6gc.net/forums/index.php?showto...32626&st=80 you CAN convert the awd to fwd. its on celicatech This post has be...
6 posts • Started by 97celiman
arent those coilovers? not just lowering springs?...
23 posts • Started by 808celica
Celica 2- andrew 0.... Now i got EVERYTHING OFF(thanks to jon) and i find that the stud that i bought it wrong,so now i get to venture back to kragen ...
3 posts • Started by celica95-95
Im not sure if you're talking about the O.E. brand that advance/autozone sells... but if you are. STAY AWAY I used to sell them. go oem instead...
22 posts • Started by _mikeE
ABS is the last thing you want in snowy icey conditions as it cuts in too early and gives you no braking power under sliding, my WRC 205 has no ABS so...
17 posts • Started by _mikeE
how did you do your rear end suspension?...
8 posts • Started by Cuts_the_Pilot
comming from all your gtfour experience pressure? they have extra bracing around the strut tower, top and bottom. the whole floorpan is different. I d...
22 posts • Started by 808celica
Ahhh i see now i only have 1 shim per pad on each rotor. but why isnt the right making noise and only the left is??? i do have some shaking under brak...
21 posts • Started by 808celica
^yup TRD springs are made by Eibach and many of toyotas shocks were/might still be made by KYB...
7 posts • Started by 97celiman
I had these coils on my old civic with a set of koni yellows and the ride was pretty straight, IM gonna run the same setup on my celly but im gonna ge...
11 posts • Started by barterj
Check your brake fluids yet? ABS doesn't always work perfectly, because my wheels still tend to lock up before it gets to a stop, but your situation i...
22 posts • Started by bccentaur3
At first I thought your tires needed balancing, but like bseaman said, you ruled that out already. It could very well be a bent tie rod, but I'm still...
3 posts • Started by 94celi757
Any problems anyone out there ran into when putting tein ss coilover on there car, did factory bushings or bearings have to be replaced at time of the...
11 posts • Started by BonzaiCelica
haha hmm... it seems by pressures response that he agrees that it doesnt do anything lol...
20 posts • Started by 95CelicaST
Eibach sportlines don't give an uneven looking drop. It looks great with them; I've gotten many compliments. On rough roads however, you're not going ...
9 posts • Started by 95st-celica
Griff I guess you're right. I never thought of that. Either way, I guess I have been doing it wrong the whole time. Oh well, my car still handles like...
14 posts • Started by 808celica
arent performance brake pads like going to wear down faster?? yeah they have less dust but they dont have much of a life span This post has been edite...
14 posts • Started by 94yoter
225/45/17 is best, but if you are concerned with looks, it kinda depends on the width of the wheel 225/45/17 on a 17x7 will look a bit beefy 225/45/17...
6 posts • Started by 94celi757
A good setup i think would be ground control coilovers with koni yellows or kybs,or k-sports coilovers, these two setups i would recommend if you are...
3 posts • Started by 808celica
haha he's sucking up to you already HAHAHAhaha...
14 posts • Started by azian_advanced
48820-33010 front, shows to be the same for both sides 48830-20010 rear, shows to be the same for both sides....
3 posts • Started by Cuts_the_Pilot
QUOTE (pipes @ Nov 27, 2008 - 11:39 AM) wondering if anyone knows this... rear axles for this thing...... are they the same for an st185? because i lo...
67 posts • Started by 3TST
...just when i thought i was settled everyone has to raise doubt again I can live with a short life span if it means highlighting my celicas handling ...
5 posts • Started by Batman722
got sorted people....... thanks batman for the reply as i suspected it was the 202 ball joint needed This post has been edited by paul_gt4 : Nov 26, 2...