Engine/Transmission/Maintenance

14,249 Total Topics
25 Showing
144 Page 144 of 570
Topics in Engine/Transmission/Maintenance • newest topics first
4 posts • Started by Bitter
Hello if anyone could help me here that would be great, on my header there is an eye shaped cap , bolt on either side that blew off or rusted off. Ca...
6 posts • Started by AnaXyd
congrats man...
7 posts • Started by azian_advanced
At last I had some time to work on my baby again. I have spend 12hours of working on it. Here are some pics and details... Main goal was get rid of th...
2 posts • Started by 97gt5sfe
Anyone have any experience with the PIVOT Raizen Hyper Voltage Stabilizer? Most people using it claim power gains....
3 posts • Started by Rook
I literally had this same problem- replaced the ignition coil, and problem solved. 30 bucks, ran like new....
5 posts • Started by Hope604
Easy to do if you have the right tools. Impossible for the tool less. Your looking at around $700-1000 depending on where you go....
12 posts • Started by EKAn
Bored one afternoon after Uni, me and my mate decided my car should start work on my car. Had it for a while now and it was completely stock. started ...
13 posts • Started by Batman722
(Finally Found the search bar at Kbox) so I guess they have some... Soul...
8 posts • Started by Johnnyny
i posted in your WTB ad, i can meet you somewhere in PA...
3 posts • Started by CelicaST96
QUOTE (CelicaST96 @ May 12, 2010 - 3:36 PM) Will a Exedy Stage 1 Clutch for an ST be compatible to a 3SGTE engine's transmission? no....
12 posts • Started by 97celiman
Also, would I need to disconnect the battery cables in order to reset the Mass Air Flow (MAF) Sensor?...
13 posts • Started by Bitter
ah....well yea that old one was pooched. uh if you drove with the starter grinding against the fly wheel like that it could have damaged the fly wheel...
2 posts • Started by 4-eyed-freek
http://www.6gc.net/forums/index.php?showtopic=52417...
16 posts • Started by 4-eyed-freek
^ ' ' you beat me .... lol QUOTE (eengineer @ May 10, 2010 - 8:22 PM) my friend bought a 94 5S-FE Celica GT-S 5speed with a blown motor he's attemptin...
21 posts • Started by 96stgreendemon
1. its not a honda 2. its a 2.2 from the camry, its made for torque and smooth power while netting decent gas mileage 3. its not a high performance e...
22 posts • Started by 94GreenLantern
^^^translate? i will post videos after i get my tach meter working, my power steering is also leaking badly so thats another problem i have to take ca...
5 posts • Started by Bitter
1995 TOYOTA CELICA GT- Car start. Move an inch, then refuse to respond to pedal push. Did have "head" problem. Used head gasket sealant about 6 months...
6 posts • Started by DJim
alright so i'm running a 5s-fe with the stock manual transmissinon as i'm upshifting, every gear goes in fine, for the most part but as i'm downshifti...
5 posts • Started by 96stgreendemon
^^ yep the exedy oem clutch kit comes with everything you need including the throw out bearing I bought mines from www.streetsideauto.com good prices ...
16 posts • Started by HectortheRican
Car is now giving off a bad carbon smell. Everytime I start it up and what not. Besides that car seems to be acting pretty normal besides the ticking,...
16 posts • Started by cyberblader1130
Any suggestions? Autozone didn't have the fuel filter so I have to call around tomorrow to find one. Can a fuel filter be clogged enough that the car ...
17 posts • Started by bccentaur3
1/3MZFE can be legal... 2ZZGE can be legal, I've seen a USDM MR2 turbo swap into a 95 Celica GT BAR'd and legal... but that's highly dependent on who ...
11 posts • Started by 95celicastLSR
Good to know that the mystery sound is now gone....
6 posts • Started by conus00
...I need to see back of the block where knock sensor connects to the engine? I found loose connector just dangling above passenger's side axle and ha...
9 posts • Started by bmj67
awesome...good to know...can u really feel the engine running. here's a pic on a forum http://www.toyotanation.com/forum/showthre...=balance+shafts...