Engine/Transmission/Maintenance

14,249 Total Topics
25 Showing
159 Page 159 of 570
Topics in Engine/Transmission/Maintenance • newest topics first
6 posts • Started by Blk94St
bump...
6 posts • Started by CelicaGTWolf
as far as I no dead on 4,000rpm is 110km (75ishmph)...
12 posts • Started by 808celica
Doesn't it go to the throttle though? When I pull the cable it moves the throttle. I am a little scared to remove it seeing that. Is it really just...
4 posts • Started by 6G96GT
Has any work been done on the 7th gen? it has a cooling system that is very difficult to bleed. If he had a coolant change then it still needs to be b...
2 posts • Started by Euphoria
Been reading and see that cams on other celica engines can really boost them. I have been looking but cant find anything Does any one have any ideas f...
21 posts • Started by 6G96GT
Finally figured it out! Turns out the heater core was clogged! Thanks for all the help This post has been edited by Dangercart1 : Dec 24, 2009 - 12:39...
5 posts • Started by DGAF
I'm back three motors later... Just got done putting a new motor in my GT. Driving it since last night, it's smoking out of the exhaust but my mechani...
3 posts • Started by vtnsx
After driving 15 minutes on snow, my engine light came on. Now, could anyone tell me what error code number this is http://www.youtube.com/watch?v=5jW...
3 posts • Started by Bitter
found another thread with similar situation, but i dont understand whats going on here. Heres the thread Simlar post... This post has been edited by G...
23 posts • Started by 95CelicaST
10-15hp from full exhaust on a 5S-FE? i doubt that....
12 posts • Started by Bitter
2zz is smooth until you bounce off rev limiter....
9 posts • Started by 3WayStunna
HOW TO GUIDE:-Fitting Guide JSP - Solid Shifter Base Bush Kit - Celica GEN 6 -:Tools required:- JSP – Solid Shifter Bush Kit Flat Blade Screwdriver Ph...
5 posts • Started by 808celica
i have a spare set of shifter cables from a 7afe corolla 97...
1 posts • Started by pipes
hey if i buy a 50mm radiator do i need new fans? or will the old fans work properly?...
6 posts • Started by bmj67
does anyone know where that wire ends up? I couldnt find it in the wiring diagrams in my chiltons...
16 posts • Started by bccentaur3
Good luck on 10 psi with the beams intake manifold. That thing isn't built for boost. You should spend some time on the mr2oc board and see what they ...
3 posts • Started by Bitter
dead diode on rectifier pack. if you have a scope, check ripple curent. it should be way off....
3 posts • Started by domyz
Found it : 33820-2b321...
11 posts • Started by 6G96GT
^ the 3rd gen rev limiter is 7,500 (apperently) and BEAMS is 7,450rpm (apperently) I'll try find the posts if anyone wants proof? EDIT: found it http:...
13 posts • Started by 96stgreendemon
94 to 95 obd 1 celica's have 2 cats one in the manifold and one after the mid pipe http://www.6gc.net/images/howto_photos/128_10.jpg http://www.6gc.ne...
17 posts • Started by bmj67
as far as available information from toyota / TRD sites, there was no viscous LSD, the part numbers for the stock MR2 LSD correspond with the mechanic...
21 posts • Started by Bitter
^^ My thoughts exactly. Whether or not the motor purchased is a JDM engine is of no relevance, so long as it's a 5S-FE. Inconsistent spark, all I can ...
11 posts • Started by AzNbOiFrM9i6
adjust IAC valve...
24 posts • Started by BonzaiCelica
^Gas mileage?...
51 posts • Started by 95st-celica