Hey guys,
I've been tracing out a problem with my blower motor, it seems that I'm not getting voltage from the 40a heater fuse from the engine bay fuse box. I pulled the fuse and checked both pins for voltage, neither has voltage. Does anyone have a power distribution wire diagram of the inside of this fuse box?
-Jay95 GT conv. project car: Manual, Gen III 3sgte, JN pisons, Eagle rods, overbore, crank knife-edged, crank scraper, ARP head/main/flywheel, Autronic EMS, Haltech Dual Wideband O2 controller, Audi 1.8T individual coils, FMIC and SSQV BOV, 3" downpipe, 3" ultra-high-flow cat, 2.5" Borla muffler, +other01 S2000: FMIC, Haltech EMS, Haltech wideband, 570cc inj, forged pistons/rods, sleeved block, 5 angle valve job, ported and polished02 R6, all stock, except for braided stainless brake lines, frame sliders, and adjustable brake/clutch leve
>
QUOTE (Jmk91 @ Aug 10, 2015 - 7:18 PM)
>
https://www.google.com/url?sa=t&source=...hk1YtUEGGtspSawSorry about long URL. Takes you.to download a PDF file. At the very bottom of PDF is diagram its for a 94 but I'd assume it's the same. Have you checked the resistor?
Thanks for the link, but I verified that most of this works today. My problem seems to lie in the main fuse box under the hood. The 40 amp main fuse has no power, and I think I might have to open up the fusebox to see why, unless I get my hands on a diagram of the main fuse box.
-Jay95 GT conv. project car: Manual, Gen III 3sgte, JN pisons, Eagle rods, overbore, crank knife-edged, crank scraper, ARP head/main/flywheel, Autronic EMS, Haltech Dual Wideband O2 controller, Audi 1.8T individual coils, FMIC and SSQV BOV, 3" downpipe, 3" ultra-high-flow cat, 2.5" Borla muffler, +other01 S2000: FMIC, Haltech EMS, Haltech wideband, 570cc inj, forged pistons/rods, sleeved block, 5 angle valve job, ported and polished02 R6, all stock, except for braided stainless brake lines, frame sliders, and adjustable brake/clutch leve
Learned a lot in 10 years...I hardly log in anymore, last loginToday Sept 6 2019, and I was forced just to clarify a post. LOLIf you PM me and I dont respond, dont fret or cry. Im alive, better post your questions in the thread below, maybe I log back in2grfe Swapped...Why I chose the 2GR, before you ask read here...A great civilization is not conquered from without until it has destroyed itself from within.@llamaraxing in Instagram is the best way to find me. I hardly log here anymore.
>
QUOTE (njccmd2002 @ Aug 11, 2015 - 8:26 PM)
I just went through the process of creating a trial adobe account just to download that, and it says I need to buy a cloud membership. meh, I give up. I'll pull one from the junkyard next week and rip it apart to see how it is wired, then fix mine. Thanks for posting the link though
-Jay95 GT conv. project car: Manual, Gen III 3sgte, JN pisons, Eagle rods, overbore, crank knife-edged, crank scraper, ARP head/main/flywheel, Autronic EMS, Haltech Dual Wideband O2 controller, Audi 1.8T individual coils, FMIC and SSQV BOV, 3" downpipe, 3" ultra-high-flow cat, 2.5" Borla muffler, +other01 S2000: FMIC, Haltech EMS, Haltech wideband, 570cc inj, forged pistons/rods, sleeved block, 5 angle valve job, ported and polished02 R6, all stock, except for braided stainless brake lines, frame sliders, and adjustable brake/clutch leve
