anyone know how to change the licence plate light. i looked on the outside and saw that all the bolts were rusted. is this how in suposte to change these.
licence plate light - 6G Celicas Forums
you can unmount hte licence plate holder,6 nuts if i remeber weel, you unplug the wire and you take it off
now you can manage to get those bolts properly wtih heavy equipement!
now you can manage to get those bolts properly wtih heavy equipement!
There are two plastic cups above the lisence plate. You'll need a phillips screwdriver. You unscrew them and pull the cup down. It's only held on by suction at this point. Once it's off you can pull the bulb out.
Don't let rust scare you. Did you even TRY?
Don't let rust scare you. Did you even TRY?
1991 MR2 - T-tops - Crimson Red - Gen3 3SGTE - Lots of moneyI'm not really an asshole, but I play one on the internet.**** Photobucket
mmm corosion scares me... i had a corroded distributor bolt and tried putting it back in and over torqued it and snammed it off in the block....
after that happening i just replace it wheter its rust or corrosion....
justy my 2 cents
This post has been edited by monkey: May 28, 2008 - 4:44 PM
after that happening i just replace it wheter its rust or corrosion....
justy my 2 cents
This post has been edited by monkey: May 28, 2008 - 4:44 PM
>
hmmm big difference here. Yours was a vital engine component. This is a screw.
QUOTE
>mmm corosion scares me... i had a corroded distributor bolt and tried putting it back in and over torqued it and snammed it off in the block....
after that happening i just replace it wheter its rust or corrosion....
after that happening i just replace it wheter its rust or corrosion....
hmmm big difference here. Yours was a vital engine component. This is a screw.
1991 MR2 - T-tops - Crimson Red - Gen3 3SGTE - Lots of moneyI'm not really an asshole, but I play one on the internet.**** Photobucket
>
>
i think he wanted to say that he cant unscrew the bolts normally because rust"eated" theyr head.
QUOTE (crash60068 @ May 24, 2008 - 12:46 AM) 
>anyone know how to change the licence plate light. i looked on the outside and saw that all the bolts were rusted. is this how in suposte to change these.
>
QUOTE (95CelicaST @ May 28, 2008 - 5:37 PM)
>There are two plastic cups above the lisence plate. You'll need a phillips screwdriver. You unscrew them and pull the cup down. It's only held on by suction at this point. Once it's off you can pull the bulb out.
Don't let rust scare you. Did you even TRY?
Don't let rust scare you. Did you even TRY?
i think he wanted to say that he cant unscrew the bolts normally because rust"eated" theyr head.
Mine were rusted beyond belief; busted out the dremel. Dont have the plastic covers anymore but its easy to change the bulb 
wat kinda bulb is it,can u change the color??is that legal?
BANNED. for life, you moron.
They're some other number but 194 fits perfect. To the best of my knowledge it is illegal in most states to change the visibility of the plate in any way - including burned out bulbs, plastic covers over plate and I'm pretty sure changing the color is enough at least to write you a ticket and mess with you about you're other mods. But IDK for sure.
ENGINE: '93 RC 3S-GTE/WRC CT-20b [18-20PSI]PERF: TRD/HKS/ARP/NGK/MSD/ACT/Blitz/STRI/APEX'i/TwosRus/GReddy/Magnaflo/KOYOSUSP: Tein/Bilstein/SusTech/INT: SS-III SEATS/Toyota Hyper SportsEXT: WRC/TRD/404QUOTE (lagos @ Aug 25, 2010 - 10:13 AM)Its a safety feature so that people like you don't end up killing themselves or everyone around them.Slow down Paul Walker.6GC Chat - Go there: [url="http://www.griffgirl.com/forum/chat/index.php[/url]
up here the law is you cant have any obstruction of your plates..even the like "midtown toyota" plate frames, illegal. But for bulbs you need white. What i did was got a set of PIAA GTX 168 bulbs for both my celica and SIR. They look like the plate bolts on the new IS350s. Really nice.
2 194 LEDs from ebay
Call me a traitor! See if I care. ;)