Penkka

#1

I´m after some aftermarket performance exhaustsystem to my 3S-GE. I´ve been looking for a while, but the only reaseonable I´ve found is Apexi N1. I also ran into HKS exhausts, but they were too expensive. Any suggestions?

Thanks allready mates.

---

320hp @ 6300rpm and 420Nm @ 3250rpm. yay!My ST205 WRC buildthread

94_c3lica_gt

#2

I've been looking for an exhaust system for my car so that when i do my 3sgte swap, the turbo will breathe better. Where did you find the apexi n1 turbo for the 6gc? or the hks? THANKS!

Penkka

#3

My Celica doesn´t have a turbo, its N/A 2.0.

---

320hp @ 6300rpm and 420Nm @ 3250rpm. yay!My ST205 WRC buildthread

Kadett

#4

The only one's I know off are:
Apexi
HKS
Kakimoto
C-one

---

JDM Powerplant installed, BPU coming very soon!

GTS13

#5

Or you could just go custom, it might cost less since the exhausts that fit our cars would have to be shipped. Find an exhaust shop and get a quote.

Penkka

#6

>

QUOTE(GTS13 @ Dec 22, 2007 - 1:33 PM) [snapback]625036[/snapback]

>
Or you could just go custom, it might cost less since the exhausts that fit our cars would have to be shipped. Find an exhaust shop and get a quote.

Yea I´ve been thinking about that too, but wich ones better, with a 2.25" bore or 2.5"?

This post has been edited by Penkka: Dec 23, 2007 - 12:13 PM

---

320hp @ 6300rpm and 420Nm @ 3250rpm. yay!My ST205 WRC buildthread

Kadett

#7

60mm is the Size that all Japanese companies used. I would use the same.

---

JDM Powerplant installed, BPU coming very soon!

99Celica

#8

60 mm equates to 2.362in which is inbetween 2.25 and 2.5in. So, which is better?

Penkka

#9

If I´ve understood correctly, 2.5" looses the highpowers, but is more torguebased. the 2.25" instead gives you more power to higher revs, correct?

---

320hp @ 6300rpm and 420Nm @ 3250rpm. yay!My ST205 WRC buildthread

99Celica

#10

"If I´ve understood correctly, 2.5" looses the highpowers, but is more torguebased. the 2.25" instead gives you more power to higher revs, correct?"

can anyone answer this? Also do one of these sound ricey? I'm ready to go to the shop but I can't decide what size.

Teksi

#11

>

QUOTE(Penkka @ Dec 20, 2007 - 4:47 PM) [snapback]624560[/snapback]

>
I´m after some aftermarket performance exhaustsystem to my 3S-GE. I´ve been looking for a while, but the only reaseonable I´ve found is Apexi N1. I also ran into HKS exhausts, but they were too expensive. Any suggestions?

Thanks allready mates.

Hei Penkka!
I have used hks super drager coming from japan. It's 60mm and it will be for sale...
I can also get other exhaust from japan if you want.


>

QUOTE

>
"If I´ve understood correctly, 2.5" looses the highpowers, but is more torguebased. the 2.25" instead gives you more power to higher revs, correct?"

It's exactly opposite you wrote...