it will work right, only thing is gas tank and exhaust need to be moved ?? can the exhaust be ran up alongside the drive shaft?
gt 4 rear end in 94 gt - 6G Celicas Forums
from what i know that the GT4 body fram is 3inches wider on each side 
what r u trying 2 do make it RWD or AWD ?
what r u trying 2 do make it RWD or AWD ?
awd
try 2 get the rear dif demitions and see if the mounting hole are the same and c if it will work
everything has to be custom fabricated or transfered over from the GT-4.
none of the mounting points are on the GT frame.
none of the mounting points are on the GT frame.
Former Team 5SFTE pro member ;)13.6@108MPH, 5SFTE Powered
the floor pan, suspension setup, control arms, mounting points are all different and dont exist on a GT car...
the GT/ST floors are lower then the GT4's rear so it doesn't allow as much clearances under the car either
the GT/ST floors are lower then the GT4's rear so it doesn't allow as much clearances under the car either
does any of the all trac cars rearends fit well? 5th gen rear end? i've seen someguys conversion but i don't know where to find it now. ?
>
And what difference would it make... sourcing a rear-end from an alltrac? All of the toyota multi-link rear-ends are pretty much the same.
Conversions have been done... but require chopping the rear end into bits then welding everything up again...
QUOTE(freakyre33c @ Aug 21, 2006 - 10:56 PM) [snapback]471354[/snapback]
>
does any of the all trac cars rearends fit well? 5th gen rear end? i've seen someguys conversion but i don't know where to find it now. ?
does any of the all trac cars rearends fit well? 5th gen rear end? i've seen someguys conversion but i don't know where to find it now. ?
And what difference would it make... sourcing a rear-end from an alltrac? All of the toyota multi-link rear-ends are pretty much the same.
Conversions have been done... but require chopping the rear end into bits then welding everything up again...
"It's ok to be naked girl... I'm an artist!"1995 AT200 Celica ST:stocked out daily driver...1984 AE86 Corolla GT-SR5:silvertop 20V 4AGE project car jacked up with goodies...1991 SW2x MR2 n/a:bare bones hardtop model soon to be...
well just down to the nut, how much chopping is there? is it even worth it? i mean if im gonna do the swap and put the awd drive into it, after all that time i might as well take everything out, stuff a roll cage in it, and dump some big bucks into it and make a ****en race car out of it !lol my point is i might as well just go full tilt and turn it into something incredible... u know what i mean?
>
basicly, you have to cut all the parts outta the gt-4 rear (or custom make a subframe, and mounting points for it), cut out the spare tire well outta your car, and start from there.
if you dont have some SERIOUS fabrication skills, its really not worth it.
celiman05 did it, with his dad doing the fabrication work on it (its what he does for a living) and even he said he would never attempt it again.
QUOTE(freakyre33c @ Aug 22, 2006 - 4:11 PM) [snapback]471651[/snapback]
>
well just down to the nut, how much chopping is there? is it even worth it? i mean if im gonna do the swap and put the awd drive into it, after all that time i might as well take everything out, stuff a roll cage in it, and dump some big bucks into it and make a ****en race car out of it !lol my point is i might as well just go full tilt and turn it into something incredible... u know what i mean?
well just down to the nut, how much chopping is there? is it even worth it? i mean if im gonna do the swap and put the awd drive into it, after all that time i might as well take everything out, stuff a roll cage in it, and dump some big bucks into it and make a ****en race car out of it !lol my point is i might as well just go full tilt and turn it into something incredible... u know what i mean?
basicly, you have to cut all the parts outta the gt-4 rear (or custom make a subframe, and mounting points for it), cut out the spare tire well outta your car, and start from there.
if you dont have some SERIOUS fabrication skills, its really not worth it.
celiman05 did it, with his dad doing the fabrication work on it (its what he does for a living) and even he said he would never attempt it again.
Former Team 5SFTE pro member ;)13.6@108MPH, 5SFTE Powered
start with sumthing like this
im a fabricator too i would be fine with that. i just wasn't sure how much stuff i would need to go through to complete this, and what about makeing sure the rearend is straight all that kind crap. how long did it take celicaman05?
This post has been edited by freakyre33c: Aug 22, 2006 - 7:48 PM
This post has been edited by freakyre33c: Aug 22, 2006 - 7:48 PM