📝 Over9000's Posts
Over9000
📍 Ontario, Canada
Member
Posts
9
Vehicles
0
7afe to BEAMS Red Top - 6G Celicas Forums
EnthusiastJoined Jun 30, '15From Ontario, CanadaCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Engine/Transmission/Maintenance
Lol, yes I did that. The wiring harness is all extended. I can't believe the newb mistakes I made earlier... Learning experience for sure lol
Just an FYI for ST swappers; The Throttle cables are not t...
Just an FYI for ST swappers; The Throttle cables are not t...
Topic ID: 95739 • Post ID: 9967274
7afe to BEAMS Red Top - 6G Celicas Forums
EnthusiastJoined Jun 30, '15From Ontario, CanadaCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Engine/Transmission/Maintenance
So you're saying I can swap my rack over(obviously) but change the inner and outer tie rods to make it compatible with the superstrut setup? That thread was a little confusing... The first guy just sw...
Topic ID: 95739 • Post ID: 9967272
7afe to BEAMS Red Top - 6G Celicas Forums
EnthusiastJoined Jun 30, '15From Ontario, CanadaCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Engine/Transmission/Maintenance
Thanks for the info richee3. The fuse box is in tact and cut right at the bottom of it, I will add the pic when I get home tonight. I've got the entire front suspension system for the superstrut, so w...
Topic ID: 95739 • Post ID: 9967269
7afe to BEAMS Red Top - 6G Celicas Forums
EnthusiastJoined Jun 30, '15From Ontario, CanadaCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Engine/Transmission/Maintenance
I picked up my engine yesterday, and noticed they cut the wiring harness under the under hood fuse box. Does anyone have the wiring diagram for the BEAMS fuse box? Also, regarding the part numbers, he...
Topic ID: 95739 • Post ID: 9967266
7afe to BEAMS Red Top - 6G Celicas Forums
EnthusiastJoined Jun 30, '15From Ontario, CanadaCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Engine/Transmission/Maintenance
Yeah, I read that article. Does explain some things regarding wiring, however I'm a little unclear of how much that thread applies to an At200... Am I the only one dumb enough to try this swap? Or doe...
Topic ID: 95739 • Post ID: 9967264
7afe to BEAMS Red Top - 6G Celicas Forums
EnthusiastJoined Jun 30, '15From Ontario, CanadaCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Engine/Transmission/Maintenance
Hi, new to the forum and can not find all the info I need for the swap I'm about to do. I have an AT200 and am swapping a beams redop in. My questions mainly have to do with Motor mount placement and ...
Topic ID: 95739 • Post ID: 9967262
How to: 3S-GE BEAMS Wiring into USDM Celica - 6G Celicas Forums
EnthusiastJoined Jun 30, '15From Ontario, CanadaCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Engine/Transmission/Maintenance
I'm looking at the 7A harness. That's where my BEAMS engine harness ends and my 7A chassis harness begins. We're supposed to bridge the wires after the box I thought...
When you said "When you remove ...
When you said "When you remove ...
Topic ID: 91456 • Post ID: 9928745
How to: 3S-GE BEAMS Wiring into USDM Celica - 6G Celicas Forums
EnthusiastJoined Jun 30, '15From Ontario, CanadaCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Engine/Transmission/Maintenance
Has anyone ran into the issue of not having pins 17 or 12 on their ae1? In that case would I be able to bridge it before the connector on the other side? Or should I add a pin to those?
Topic ID: 91456 • Post ID: 9928743
Celica RWD - 6G Celicas Forums
EnthusiastJoined Jun 30, '15From Ontario, CanadaCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Engine/Transmission/Maintenance
say it is feasible to put this in, you could use the 90's Mustang Rack like in the other thread, and possibly us the Toyota Altezza Lexus IS300 SXE10 setup with the black top. That would (I think) be ...
Topic ID: 68707 • Post ID: 9386938
Showing page 1 of 1 (9 total posts)