📝 Justen's Posts
FS: 7afe engine block and cylinder head and misc wth pics! - 6G Celicas Forums
EnthusiastJoined May 17, '08From North Liberty, INCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Buying/Selling
where at in michigan are you? ball park what you would want for the short block?
Topic ID: 68219 • Post ID: 9381633
WTB:7afe crankshaft pulley - 6G Celicas Forums
EnthusiastJoined May 17, '08From North Liberty, INCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Buying/Selling
$20+ shipping sound good?
Topic ID: 67350 • Post ID: 9331169
struts? - 6G Celicas Forums
EnthusiastJoined May 17, '08From North Liberty, INCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Suspension/Handling/Braking
i just put some ebay coilovers on my car. the rear has the sleeve turned like 5 turn up and the front has no sleeve. my car sits like 2" off the ground with stock struts. the struts bottom out on like...
Topic ID: 67052 • Post ID: 9327803
FS 7AFE Parts and 5 Speed Tranny - 6G Celicas Forums
EnthusiastJoined May 17, '08From North Liberty, INCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Buying/Selling
what you want for the short block?
Topic ID: 66564 • Post ID: 9200497
drag radials on stock wheels or on my aftermarket 17's ? - 6G Celicas Forums
EnthusiastJoined May 17, '08From North Liberty, INCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Suspension/Handling/Braking
stock would be better. the 17s need low pros which have stiffer side walls. drag radials would probably fine. im assuming your cars a stick so some wheel spin is ok, you don't want your motor to bog.
Topic ID: 66506 • Post ID: 9199960
speedometer not reading right - 6G Celicas Forums
EnthusiastJoined May 17, '08From North Liberty, INCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Engine/Transmission/Maintenance
any 5sp st owners know how many rpm they turn at 60mph?
Topic ID: 66464 • Post ID: 9199520
speedometer not reading right - 6G Celicas Forums
EnthusiastJoined May 17, '08From North Liberty, INCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Engine/Transmission/Maintenance
is that what your speedometer reads at 3k? its like around 2200 RPM at 60 mph
Topic ID: 66464 • Post ID: 9199517
speedometer not reading right - 6G Celicas Forums
EnthusiastJoined May 17, '08From North Liberty, INCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Engine/Transmission/Maintenance
i have a 94 celica st 5sp. i think the speedometer is saying im going faster than what i am. at 3k rpm it says im doing about 73mph. does that sound right? i have 205/60-14 on it so that might throw i...
Topic ID: 66464 • Post ID: 9199515
*SOLD* please lock :) - 6G Celicas Forums
EnthusiastJoined May 17, '08From North Liberty, INCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Buying/Selling
do the wheels have any damage? what brand are they?
Topic ID: 66459 • Post ID: 9199431
Machine shop quotes - 6G Celicas Forums
EnthusiastJoined May 17, '08From North Liberty, INCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Engine/Transmission/Maintenance
QUOTE (pittfirefighter @ Mar 26, 2009 - 11:04 PM)
just go shimless if you get your head worked on... cost me $200 to get my head done... shims included... block is going to cost you more... usually ab...
just go shimless if you get your head worked on... cost me $200 to get my head done... shims included... block is going to cost you more... usually ab...
Topic ID: 66286 • Post ID: 9197685
Machine shop quotes - 6G Celicas Forums
EnthusiastJoined May 17, '08From North Liberty, INCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Engine/Transmission/Maintenance
i got my head resurfaced and the valves grinded for about $130. but some machine shops won't touch the head because of all the work involved in shimming it. i had to do the shims myself but the guy at...
Topic ID: 66286 • Post ID: 9197683
Changing Transmission Seal E-153 Is it hard? - 6G Celicas Forums
EnthusiastJoined May 17, '08From North Liberty, INCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Engine/Transmission/Maintenance
Replacing the seals isn't that hard. you have to take the lower part of the strut loose, outer tie rod end, and pull the axle out. use a seal puller tool or pry bar to remove and the proper seal drive...
Topic ID: 66269 • Post ID: 9197568
alrighty, may seem simple but still... - 6G Celicas Forums
EnthusiastJoined May 17, '08From North Liberty, INCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Suspension/Handling/Braking
if you pump the brakes with the bleeder loose your gonna push air and fluid out and suck air back in. you should have the bleeder close when pumping, hold the pedal and loosen the bleeder. then tighte...
Topic ID: 66240 • Post ID: 9195160
TANABE DF210 - 6G Celicas Forums
EnthusiastJoined May 17, '08From North Liberty, INCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Suspension/Handling/Braking
i got these DF210 for my car and i don't think its dropped as much as it said it was suppose to. how long does its take for them to settle?, the tanabe rep told me 2 weeks. its been about that long an...
Topic ID: 65801 • Post ID: 9190423
drive shaft problem - 6G Celicas Forums
EnthusiastJoined May 17, '08From North Liberty, INCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Engine/Transmission/Maintenance
there should be a castle nut and cotter pin that goes on there to stop it from coming loose.
Topic ID: 60664 • Post ID: 8801223
what engine will fit - 6G Celicas Forums
EnthusiastJoined May 17, '08From North Liberty, INCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Engine/Transmission/Maintenance
will a 7afe out of a 97 corolla work ok in my 94 celica?
Topic ID: 60663 • Post ID: 8801219
Transmission question - 6G Celicas Forums
EnthusiastJoined May 17, '08From North Liberty, INCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Engine/Transmission/Maintenance
so 5gen celica has s53 and 6gen has s54? is there any differences? which does the camary have? is the a difference between the 5sfe cluctch and the 3sgte clutch as far as splines and bolting it to the...
Topic ID: 58697 • Post ID: 8532428
Transmission question - 6G Celicas Forums
EnthusiastJoined May 17, '08From North Liberty, INCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Engine/Transmission/Maintenance
I have a 94 st, i want to swap in a 3sgte. i was going to just use a 5sfe trans but i was wondering if the 5sfe trans out of a camary or earlier model celicas would wok and if what the transmission co...
Topic ID: 58697 • Post ID: 8532426
FS parting out a 94 st coupe - 6G Celicas Forums
EnthusiastJoined May 17, '08From North Liberty, INCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Buying/Selling
QUOTE (crash60068 @ May 15, 2008 - 6:34 PM)
ok if anyone need parts i have a most of a 94 st left. mostly is body work and some mechanical parts too but not much. let me if you need anything
is the mo...
ok if anyone need parts i have a most of a 94 st left. mostly is body work and some mechanical parts too but not much. let me if you need anything
is the mo...
Topic ID: 58515 • Post ID: 8530677
FS:Clutch Masters Light Weight FlyWheel 7afe - 6G Celicas Forums
EnthusiastJoined May 17, '08From North Liberty, INCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Buying/Selling
im interestd. how much does it weigh compared to stock? whats shipping to 46554. roughly how many miles on it? could you email me some pics? thanks
Topic ID: 58500 • Post ID: 8530465
Showing page 1 of 2 (21 total posts)