📝 Hafkai's Posts
MS3PRO EVO on 4th Gen 3sgte - 6G Celicas Forums
EnthusiastJoined Dec 9, '05From GermanyCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Forced Induction
QUOTE (HardHead93 @ Sep 25, 2017 - 2:33 AM)
Does anyone know how to check timing with a coil on plug setup? There is nowhere to hook up my timing light.
This is how i do it
Works perfect
Does anyone know how to check timing with a coil on plug setup? There is nowhere to hook up my timing light.
This is how i do it
Works perfect
Topic ID: 97949 • Post ID: 9985181
Crankshaft/flywheel dimensions - 6G Celicas Forums
EnthusiastJoined Dec 9, '05From GermanyCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Engine/Transmission/Maintenance
I tried to measure the crankshaft as good as possible...
Topic ID: 97346 • Post ID: 9979489
AN 10 fitting for turbo return - 6G Celicas Forums
EnthusiastJoined Dec 9, '05From GermanyCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Forced Induction
I wouldn't put the oil return in the lower oil pan, the return should be above the oil level so it can flow freely. You should try to get a fitting in the upper aluminum oil pan.
Topic ID: 95489 • Post ID: 9965718
3 Point Rear Strut Braces - 6G Celicas Forums
EnthusiastJoined Dec 9, '05From GermanyCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Suspension/Handling/Braking
I just modified my factory strut brace, the steel tubes cost me ~5$ and another 15$ for some gray metallic paint to match the front trd strut brace.
Topic ID: 94180 • Post ID: 9959112
Potential 5S-FE Rod Bolt replacements? - 6G Celicas Forums
EnthusiastJoined Dec 9, '05From GermanyCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Engine/Transmission/Maintenance
QUOTE (Syaoran @ Jan 20, 2014 - 10:13 PM)
...Next I need a 7A-FE rod bolt to see if the pitch is M9x1.00....
I just measured one and it seems that M9x1.00 is correct
...Next I need a 7A-FE rod bolt to see if the pitch is M9x1.00....
I just measured one and it seems that M9x1.00 is correct
Topic ID: 91705 • Post ID: 9931318
Selfmade Sequential Shift Light - 6G Celicas Forums
EnthusiastJoined Dec 9, '05From GermanyCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Interior/Audio/Electrical/Wiring
QUOTE (angel_st @ Nov 29, 2013 - 5:02 PM)
It is really impressive, good work. I have a question, where to get the rpm signal?
I took the rpm signal from my EMS Motorsport ECU but you can take any sign...
It is really impressive, good work. I have a question, where to get the rpm signal?
I took the rpm signal from my EMS Motorsport ECU but you can take any sign...
Topic ID: 91125 • Post ID: 9925939
Selfmade Sequential Shift Light - 6G Celicas Forums
EnthusiastJoined Dec 9, '05From GermanyCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Interior/Audio/Electrical/Wiring
This is basically how i made it, would have been a lot easier with normal LEDs but i wanted them all to be able to blink blue so i had to use RGB LEDs.
I put 1000-2000 Ohm resistors in front of every ...
I put 1000-2000 Ohm resistors in front of every ...
Topic ID: 91125 • Post ID: 9925936
Selfmade Sequential Shift Light - 6G Celicas Forums
EnthusiastJoined Dec 9, '05From GermanyCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Interior/Audio/Electrical/Wiring
It´s not the most usefull thing but i just felt the urge to build something like this
.... the core of this little project is a Arduino Micro, a very small but capable microcontroller board. I´m not a...
.... the core of this little project is a Arduino Micro, a very small but capable microcontroller board. I´m not a...
Topic ID: 91125 • Post ID: 9925931
Cold start 3rd gen 3sgte issue - 6G Celicas Forums
EnthusiastJoined Dec 9, '05From GermanyCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Forced Induction
The bouncing idle seems to be caused by the deceleration fuel cut off, with the engine warmed up it cuts fuel till ~1100rpm i think, on a cold start this point could be at ~2000rpm. A vac leak could b...
Topic ID: 91046 • Post ID: 9925630
3SFTE A/F Ratio advice - 6G Celicas Forums
EnthusiastJoined Dec 9, '05From GermanyCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Forced Induction
Well, my e-Manage was able to retard and advance the timing how i wanted it, all the others i know around here are able to do the same and it works quite ok.
The part about the 2 ECUs is true and i do...
The part about the 2 ECUs is true and i do...
Topic ID: 90182 • Post ID: 9915890
3SFTE A/F Ratio advice - 6G Celicas Forums
EnthusiastJoined Dec 9, '05From GermanyCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Forced Induction
QUOTE (Smaay @ Jul 24, 2013 - 4:09 PM)
...Im not sure why everyone is ragging on the Emanage, its not a bad device....
Maybe because they never worked with one, the e-Manage Ultimate is one of the fin...
...Im not sure why everyone is ragging on the Emanage, its not a bad device....
Maybe because they never worked with one, the e-Manage Ultimate is one of the fin...
Topic ID: 90182 • Post ID: 9915888
Multifunction gauge? - 6G Celicas Forums
EnthusiastJoined Dec 9, '05From GermanyCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Forced Induction
Maybe this is something for you
Zeitronix
Zeitronix
Topic ID: 89987 • Post ID: 9817905
How thick should my spacers be? - 6G Celicas Forums
EnthusiastJoined Dec 9, '05From GermanyCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Suspension/Handling/Braking
Btw... camber is about 2,5° in front and 1,5° in rear
Topic ID: 89836 • Post ID: 9816424
How thick should my spacers be? - 6G Celicas Forums
EnthusiastJoined Dec 9, '05From GermanyCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Suspension/Handling/Braking
I got 15mm spacers in the front and 20mm in the rear, 16x7 OZ Ultraleggera ET35 and 205/55 tires.
Topic ID: 89836 • Post ID: 9816422
individual coil signal to tach :( - 6G Celicas Forums
EnthusiastJoined Dec 9, '05From GermanyCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Forced Induction
QUOTE (Smaay @ Sep 10, 2013 - 2:11 AM)
oooohhh, interesting, will this work with the stock ECU?
I completely forgot to reply
... it should work with the IGT signal if you dont use the stock ignition s...
oooohhh, interesting, will this work with the stock ECU?
I completely forgot to reply
... it should work with the IGT signal if you dont use the stock ignition s...
Topic ID: 89365 • Post ID: 9810137
individual coil signal to tach :( - 6G Celicas Forums
EnthusiastJoined Dec 9, '05From GermanyCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Forced Induction
I left the 43k ohm resistor in place (the one under the 1.0k) because it wont have any effect and i was to lazy to remove it
....
The 0,56k Pullup is only needed when the ECU doesn't output a positive...
....
The 0,56k Pullup is only needed when the ECU doesn't output a positive...
Topic ID: 89365 • Post ID: 9810135
individual coil signal to tach :( - 6G Celicas Forums
EnthusiastJoined Dec 9, '05From GermanyCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Forced Induction
There is a quite easy way to get our stock tach working with most aftermarket ECU signals. You just have to take out your tach and take a look at the circuit board, there is a ~43kohm resistor between...
Topic ID: 89365 • Post ID: 9810133
getting my engine shipped from jdm engine zone in nj - 6G Celicas Forums
EnthusiastJoined Dec 9, '05From GermanyCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Engine/Transmission/Maintenance
I'm not sure about the JDM versions but in EU the 7A-FE with two coil packs instead of the distributor is less powerfull and a lean burn engine. They got a pretty different cylinder head and engine ma...
Topic ID: 82598 • Post ID: 9660261
jdm 7afe engine swap - 6G Celicas Forums
EnthusiastJoined Dec 9, '05From GermanyCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Engine/Transmission/Maintenance
QUOTE (stormmage88 @ Mar 1, 2012 - 6:27 AM)
...could i just use mine and put my distributor on the jdm motor?
Your old distributor won't fit on a 7A with coil packs since there is a hall sensor in its...
...could i just use mine and put my distributor on the jdm motor?
Your old distributor won't fit on a 7A with coil packs since there is a hall sensor in its...
Topic ID: 82596 • Post ID: 9660246
7A-FE lack of power - 6G Celicas Forums
EnthusiastJoined Dec 9, '05From GermanyCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Engine/Transmission/Maintenance
QUOTE (Grega @ Dec 23, 2011 - 2:11 PM)
..was not lined up with the arrow that marks where dot must be..
The arrow on the bearing cap has nothing to do with the dot on the camshaft
..the dots are there...
..was not lined up with the arrow that marks where dot must be..
The arrow on the bearing cap has nothing to do with the dot on the camshaft
..the dots are there...
Topic ID: 81881 • Post ID: 9649720
Showing page 1 of 8 (144 total posts)