📝 Ewie's Posts
Ewie
📍 South Africa
Member
Posts
36
Vehicles
0
Upgrade to my 7age 16v build - 6G Celicas Forums
EnthusiastJoined Jun 10, '08From South AfricaCurrentlyOfflineReputation:0(0%)
Other
› Off Topic
http://www.tolken.co.za/twincamforum/viewt...145&start=0
Topic ID: 78251 • Post ID: 9561152
Ewie's 7AGE build - 6G Celicas Forums
EnthusiastJoined Jun 10, '08From South AfricaCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Engine/Transmission/Maintenance
Upgrade to my 7AGE with dyno sheet.
Ive changed to a ser3 smallport head (gasflowed and polished with 292deg 9mm lift cams) Comp ratio is past 12:1.
Here you can see the difference in the lobbes betwe...
Ive changed to a ser3 smallport head (gasflowed and polished with 292deg 9mm lift cams) Comp ratio is past 12:1.
Here you can see the difference in the lobbes betwe...
Topic ID: 68083 • Post ID: 9340393
Ewie's 7AGE build - 6G Celicas Forums
EnthusiastJoined Jun 10, '08From South AfricaCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Engine/Transmission/Maintenance
QUOTE (Stambo @ Aug 16, 2009 - 11:07 AM)
So 20v pistons will fit no problem in the 7a than?
They do fit in the block,both are 81mm in std size.They how ever dont fit on the conrods as the 7a have pres...
So 20v pistons will fit no problem in the 7a than?
They do fit in the block,both are 81mm in std size.They how ever dont fit on the conrods as the 7a have pres...
Topic ID: 68083 • Post ID: 9340387
Ewie's 7AGE build - 6G Celicas Forums
EnthusiastJoined Jun 10, '08From South AfricaCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Engine/Transmission/Maintenance
I used my 7afe's pully to get TDC with the mark on the oil pump and just swopped the pully again with a 4age pully.Made a new mark on it again for future rev.
Anyways,theres new plans again,bought a S...
Anyways,theres new plans again,bought a S...
Topic ID: 68083 • Post ID: 9340385
Ewie's 7AGE build - 6G Celicas Forums
EnthusiastJoined Jun 10, '08From South AfricaCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Engine/Transmission/Maintenance
QUOTE (zoik @ Jul 13, 2009 - 9:52 PM)
so? any dyno results?
Not yet bro.
The engine did just over 2000km and had 3 oil changes.
The cams need to be advanced a bit as I cant seem to get it to rev past ...
so? any dyno results?
Not yet bro.
The engine did just over 2000km and had 3 oil changes.
The cams need to be advanced a bit as I cant seem to get it to rev past ...
Topic ID: 68083 • Post ID: 9340381
Ewie's 7AGE build - 6G Celicas Forums
EnthusiastJoined Jun 10, '08From South AfricaCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Engine/Transmission/Maintenance
Im not reving past 6000 YET,as the motor still feels stiff,but the motor will be reved to 8000 when ready
Topic ID: 68083 • Post ID: 9340379
Ewie's 7AGE build - 6G Celicas Forums
EnthusiastJoined Jun 10, '08From South AfricaCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Engine/Transmission/Maintenance
Thanx guys.
The engine has done 820km thusfar,changed the oil on 600km.Wil do another 1200km b4 I put it on a dyno.
The engine has done 820km thusfar,changed the oil on 600km.Wil do another 1200km b4 I put it on a dyno.
Topic ID: 68083 • Post ID: 9340377
Ewie's 7AGE build - 6G Celicas Forums
EnthusiastJoined Jun 10, '08From South AfricaCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Engine/Transmission/Maintenance
QUOTE (Stambo @ Jun 24, 2009 - 10:01 PM)
gonna get numbers any time soon?
I dont drive the car that much so the milage pics up slow.When the engine is run in,ITB's and ECU fitted I'll have it Dynotune...
gonna get numbers any time soon?
I dont drive the car that much so the milage pics up slow.When the engine is run in,ITB's and ECU fitted I'll have it Dynotune...
Topic ID: 68083 • Post ID: 9340369
Ewie's 7AGE build - 6G Celicas Forums
EnthusiastJoined Jun 10, '08From South AfricaCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Engine/Transmission/Maintenance
QUOTE (Bitter @ Jun 24, 2009 - 8:25 PM)
if i may make a suggestion, some other 4age's used a tubular steel manifold that'll save you a few lbs vs the cast iron peice and should be easier to port match...
if i may make a suggestion, some other 4age's used a tubular steel manifold that'll save you a few lbs vs the cast iron peice and should be easier to port match...
Topic ID: 68083 • Post ID: 9340368
Ewie's 7AGE build - 6G Celicas Forums
EnthusiastJoined Jun 10, '08From South AfricaCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Engine/Transmission/Maintenance
Here's my write up on building a 7age using a ser1 Bigport head and opviously a 7afe bottomend.
I'm writing the build in 2 sections: section 1 is the history behind the build,the initial ideas and why...
I'm writing the build in 2 sections: section 1 is the history behind the build,the initial ideas and why...
Topic ID: 68083 • Post ID: 9340364
Toyota Metal Headgaskets - 6G Celicas Forums
EnthusiastJoined Jun 10, '08From South AfricaCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Engine/Transmission/Maintenance
Can the Toyota and/or TRD metal headgaskets be re-used?
Topic ID: 64659 • Post ID: 9081781
7AFE cranks - 6G Celicas Forums
EnthusiastJoined Jun 10, '08From South AfricaCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Engine/Transmission/Maintenance
QUOTE (nik @ Sep 26, 2008 - 2:08 PM)
the 7afe crank is plenty strong i have been beating on it for 2 years with over 400 horse
What rods are you using?
the 7afe crank is plenty strong i have been beating on it for 2 years with over 400 horse
What rods are you using?
Topic ID: 62255 • Post ID: 8841966
7AFE cranks - 6G Celicas Forums
EnthusiastJoined Jun 10, '08From South AfricaCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Engine/Transmission/Maintenance
Ok.Found out from our local TRD tuner that the 7AFE have a cast iron crank and so do ALL toyota's
Topic ID: 62255 • Post ID: 8841963
7AFE cranks - 6G Celicas Forums
EnthusiastJoined Jun 10, '08From South AfricaCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Engine/Transmission/Maintenance
Can anybody tell me what type crank the 7afe have.
Is it steel forged or cast?
Is it steel forged or cast?
Topic ID: 62255 • Post ID: 8841962
stock throttle body size? - 6G Celicas Forums
EnthusiastJoined Jun 10, '08From South AfricaCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Forced Induction
QUOTE (95st-celica @ Sep 16, 2008 - 4:31 PM)
bump anyone?
55mm
bump anyone?
55mm
Topic ID: 62051 • Post ID: 8839619
My 7AFE t-vis technical tread - 6G Celicas Forums
EnthusiastJoined Jun 10, '08From South AfricaCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Engine/Transmission/Maintenance
QUOTE (Bitter @ Sep 17, 2008 - 7:29 AM)
see what i mean about the non tvis port being larger than the tvis ports? though i'd love if you measured and figured area to see if its any real difference.
Y...
see what i mean about the non tvis port being larger than the tvis ports? though i'd love if you measured and figured area to see if its any real difference.
Y...
Topic ID: 61269 • Post ID: 8809132
My 7AFE t-vis technical tread - 6G Celicas Forums
EnthusiastJoined Jun 10, '08From South AfricaCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Engine/Transmission/Maintenance
Some extra info and pics added on page 2 of the link regarding the intake tvis plate and fueling.
http://www.tolken.co.za/twincamforum/viewt...p=469673#469673
http://www.tolken.co.za/twincamforum/viewt...p=469673#469673
Topic ID: 61269 • Post ID: 8809130
My 7AFE t-vis technical tread - 6G Celicas Forums
EnthusiastJoined Jun 10, '08From South AfricaCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Engine/Transmission/Maintenance
QUOTE (EXXX_AE86 @ Aug 20, 2008 - 3:38 PM)
QUOTE (Ewie @ Aug 20, 2008 - 2:29 PM)
QUOTE (EXXX_AE86 @ Aug 20, 2008 - 10:09 AM)
how much did you pick up the engine for?
Don't know what the currency is at...
QUOTE (Ewie @ Aug 20, 2008 - 2:29 PM)
QUOTE (EXXX_AE86 @ Aug 20, 2008 - 10:09 AM)
how much did you pick up the engine for?
Don't know what the currency is at...
Topic ID: 61269 • Post ID: 8809129
My 7AFE t-vis technical tread - 6G Celicas Forums
EnthusiastJoined Jun 10, '08From South AfricaCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Engine/Transmission/Maintenance
QUOTE (Bitter @ Aug 20, 2008 - 8:26 PM)
QUOTE (Ewie @ Aug 20, 2008 - 12:39 AM)
QUOTE (Bitter @ Aug 19, 2008 - 8:23 PM)
QUOTE (Ewie @ Aug 19, 2008 - 3:59 AM)
QUOTE (Bitter @ Aug 18, 2008 - 9:33 PM)
i r...
QUOTE (Ewie @ Aug 20, 2008 - 12:39 AM)
QUOTE (Bitter @ Aug 19, 2008 - 8:23 PM)
QUOTE (Ewie @ Aug 19, 2008 - 3:59 AM)
QUOTE (Bitter @ Aug 18, 2008 - 9:33 PM)
i r...
Topic ID: 61269 • Post ID: 8809128
My 7AFE t-vis technical tread - 6G Celicas Forums
EnthusiastJoined Jun 10, '08From South AfricaCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Engine/Transmission/Maintenance
QUOTE (EXXX_AE86 @ Aug 20, 2008 - 10:09 AM)
how much did you pick up the engine for?
Don't know what the currency is at he moment but I paid 4500 South African Rand for it which is quite reasonable ar...
how much did you pick up the engine for?
Don't know what the currency is at he moment but I paid 4500 South African Rand for it which is quite reasonable ar...
Topic ID: 61269 • Post ID: 8809125
Showing page 1 of 2 (36 total posts)