📝 j0ch0a94ST's Posts
Please Help! - 6G Celicas Forums
EnthusiastJoined Sep 27, '07From Raleigh, NCCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Engine/Transmission/Maintenance
So we tested the vacuum and it was at 21hg, I unplugged the MAP sensor and the car ran worse so the sensor is not necessarily bad but may be misreading. I'm going to a junkyard tomorrow to pick up ano...
Topic ID: 81060 • Post ID: 9640303
Please Help! - 6G Celicas Forums
EnthusiastJoined Sep 27, '07From Raleigh, NCCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Engine/Transmission/Maintenance
QUOTE (rave2n @ Oct 25, 2011 - 3:38 PM)
This may sound stupid, but is your e-brake stuck in position?
Cause if compression is good, timing is good...i'm confused =P
Nah man the e-brake releases proper...
This may sound stupid, but is your e-brake stuck in position?
Cause if compression is good, timing is good...i'm confused =P
Nah man the e-brake releases proper...
Topic ID: 81060 • Post ID: 9640297
Please Help! - 6G Celicas Forums
EnthusiastJoined Sep 27, '07From Raleigh, NCCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Engine/Transmission/Maintenance
QUOTE (ricochet1490 @ Oct 23, 2011 - 11:45 PM)
did you get everything figured out?
Throwing the vacuum gauge on it sometime this week
did you get everything figured out?
Throwing the vacuum gauge on it sometime this week
Topic ID: 81060 • Post ID: 9640294
Please Help! - 6G Celicas Forums
EnthusiastJoined Sep 27, '07From Raleigh, NCCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Engine/Transmission/Maintenance
QUOTE (stephen_lee @ Oct 16, 2011 - 1:13 PM)
air will leak pass the rings when u spin the motor slowly. you hear this
Thanks man it is appreciated. I wasn't sure if that was normal. However you have a...
air will leak pass the rings when u spin the motor slowly. you hear this
Thanks man it is appreciated. I wasn't sure if that was normal. However you have a...
Topic ID: 81060 • Post ID: 9640292
Please Help! - 6G Celicas Forums
EnthusiastJoined Sep 27, '07From Raleigh, NCCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Engine/Transmission/Maintenance
QUOTE (stephen_lee @ Oct 2, 2011 - 1:50 PM)
turn engine till notch on crank pulley lines up wit the 0* mark on the timin cover. pull valve cover off. hole in timing gear should match with notch in cam...
turn engine till notch on crank pulley lines up wit the 0* mark on the timin cover. pull valve cover off. hole in timing gear should match with notch in cam...
Topic ID: 81060 • Post ID: 9640289
Please Help! - 6G Celicas Forums
EnthusiastJoined Sep 27, '07From Raleigh, NCCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Engine/Transmission/Maintenance
QUOTE (d3ath2009 @ Oct 13, 2011 - 7:02 PM)
That vid actual doesnt help your case any. That performance is about right for the 7a. Idk what kind of performance you were getting before, but anything mor...
That vid actual doesnt help your case any. That performance is about right for the 7a. Idk what kind of performance you were getting before, but anything mor...
Topic ID: 81060 • Post ID: 9640286
Please Help! - 6G Celicas Forums
EnthusiastJoined Sep 27, '07From Raleigh, NCCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Engine/Transmission/Maintenance
Here's a 0-55ish video we took to show how slow it is now. We're pretty sure it slipped timing. So we'll take off the valve cover tomorrow to check like you guys suggested.
http://youtu.be/WpSvCfQJCJ0
http://youtu.be/WpSvCfQJCJ0
Topic ID: 81060 • Post ID: 9640282
Please Help! - 6G Celicas Forums
EnthusiastJoined Sep 27, '07From Raleigh, NCCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Engine/Transmission/Maintenance
QUOTE (Rav4Race @ Oct 3, 2011 - 2:50 AM)
may i know what kind of power loss is it? is turbo boosting correctly? how many psi? or is it an hesitation power loss?
Yeah man sorry no turbo here. Wish we h...
may i know what kind of power loss is it? is turbo boosting correctly? how many psi? or is it an hesitation power loss?
Yeah man sorry no turbo here. Wish we h...
Topic ID: 81060 • Post ID: 9640281
Please Help! - 6G Celicas Forums
EnthusiastJoined Sep 27, '07From Raleigh, NCCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Engine/Transmission/Maintenance
sorry guys I meant to put that I've already replaced cap and rotor
jumping a tooth may be a possibility b/c I haven't had the timing cover off to check
jumping a tooth may be a possibility b/c I haven't had the timing cover off to check
Topic ID: 81060 • Post ID: 9640276
Please Help! - 6G Celicas Forums
EnthusiastJoined Sep 27, '07From Raleigh, NCCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Engine/Transmission/Maintenance
Sorry guys. Little back story. Took the car to the carwash. Pressurewashed bay (grocery bag over dizzy etc. Left the carwash and had subbie sounding celica so I pulled over and one of the connections ...
Topic ID: 81060 • Post ID: 9640272
Please Help! - 6G Celicas Forums
EnthusiastJoined Sep 27, '07From Raleigh, NCCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Engine/Transmission/Maintenance
Sorry guys. Little back story. Took the car to the carwash. Pressurewashed bay (grocery bag over dizzy etc. Left the carwash and had subbie sounding celica so I pulled over and one of the connections ...
Topic ID: 81060 • Post ID: 9640271
Please Help! - 6G Celicas Forums
EnthusiastJoined Sep 27, '07From Raleigh, NCCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Engine/Transmission/Maintenance
K guys so its been months now and my celica is still down on power. I've had other people who have had 6th gen st's drive it and they say the same. Like I stated earlier in the thread my friend advanc...
Topic ID: 81060 • Post ID: 9640266
FS/FT: 17" MSR 8 Spoke Wheels $400 obo in NC - 6G Celicas Forums
EnthusiastJoined Sep 27, '07From Raleigh, NCCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Buying/Selling
QUOTE (ricochet1490 @ Oct 25, 2011 - 12:09 PM)
i've got em in ohio lol. 2 full sets actually
If only you were closer
i've got em in ohio lol. 2 full sets actually
If only you were closer
Topic ID: 81059 • Post ID: 9640259
FS/FT: 17" MSR 8 Spoke Wheels $400 obo in NC - 6G Celicas Forums
EnthusiastJoined Sep 27, '07From Raleigh, NCCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Buying/Selling
Anyone have factory GT 5 spokes located near NC?
Topic ID: 81059 • Post ID: 9640257
FS/FT: 17" MSR 8 Spoke Wheels $400 obo in NC - 6G Celicas Forums
EnthusiastJoined Sep 27, '07From Raleigh, NCCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Buying/Selling
QUOTE (96stgreendemon @ Oct 5, 2011 - 8:17 PM)
Pm me and we can discuss this
PM sent
This post has been edited by
j0ch0a94ST
: Oct 7, 2011 - 4:14 PM
Pm me and we can discuss this
PM sent
This post has been edited by
j0ch0a94ST
: Oct 7, 2011 - 4:14 PM
Topic ID: 81059 • Post ID: 9640256
FS/FT: 17" MSR 8 Spoke Wheels $400 obo in NC - 6G Celicas Forums
EnthusiastJoined Sep 27, '07From Raleigh, NCCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Buying/Selling
QUOTE (96stgreendemon @ Oct 4, 2011 - 10:41 AM)
They are definitey hx700 205 50 16, and I'm going to import alliance november 13th if you would want to meet there
Didn't want you to think I forgot abo...
They are definitey hx700 205 50 16, and I'm going to import alliance november 13th if you would want to meet there
Didn't want you to think I forgot abo...
Topic ID: 81059 • Post ID: 9640254
FS/FT: 17" MSR 8 Spoke Wheels $400 obo in NC - 6G Celicas Forums
EnthusiastJoined Sep 27, '07From Raleigh, NCCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Buying/Selling
QUOTE (96stgreendemon @ Oct 3, 2011 - 2:03 PM)
What Is the offset on them? May be willin to trade for 7th gen GTS WHEELS
Hey man I'll find out the offset today and let you know. I'm not sure off hand....
What Is the offset on them? May be willin to trade for 7th gen GTS WHEELS
Hey man I'll find out the offset today and let you know. I'm not sure off hand....
Topic ID: 81059 • Post ID: 9640252
FS/FT: 17" MSR 8 Spoke Wheels $400 obo in NC - 6G Celicas Forums
EnthusiastJoined Sep 27, '07From Raleigh, NCCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Buying/Selling
bump for updated pic
Topic ID: 81059 • Post ID: 9640249
FS/FT: 17" MSR 8 Spoke Wheels $400 obo in NC - 6G Celicas Forums
EnthusiastJoined Sep 27, '07From Raleigh, NCCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Buying/Selling
bump
This post has been edited by
j0ch0a94ST
: Oct 1, 2011 - 11:25 PM
This post has been edited by
j0ch0a94ST
: Oct 1, 2011 - 11:25 PM
Topic ID: 81059 • Post ID: 9640248
FS/FT: 17" MSR 8 Spoke Wheels $400 obo in NC - 6G Celicas Forums
EnthusiastJoined Sep 27, '07From Raleigh, NCCurrentlyOfflineReputation:0(0%)
6th Generation Celica
› Buying/Selling
As the title states I have a full set(4) of 17x9 MSR 8 Spoke Hypermesh 5x100 wheels that are in good condition all with good tires with tread. The wheels were originally brushed alluminum finish but h...
Topic ID: 81059 • Post ID: 9640247
Showing page 3 of 10 (190 total posts)