📝 presure2's Posts
5sfe Cams - 6G Celicas Forums
ModeratorJoined Oct 1, '02From fall river, maCurrentlyOfflineReputation:13(100%)
6th Generation Celica
› Engine/Transmission/Maintenance
with mild cams, it will run ok without tuning, but ideally you'd use something to optimize fueling for the cams.
Topic ID: 98962 • Post ID: 9993217
5sfe Cams - 6G Celicas Forums
ModeratorJoined Oct 1, '02From fall river, maCurrentlyOfflineReputation:13(100%)
6th Generation Celica
› Engine/Transmission/Maintenance
Yup, its definetly a case of measure 100x, order shims if needed, then realize a couple measurements wernt perfect, reorder, ect...lol
Topic ID: 98962 • Post ID: 9993214
5sfe Cams - 6G Celicas Forums
ModeratorJoined Oct 1, '02From fall river, maCurrentlyOfflineReputation:13(100%)
6th Generation Celica
› Engine/Transmission/Maintenance
you wont know till you put them in and measure clearances.
Topic ID: 98962 • Post ID: 9993212
5sfe Cams - 6G Celicas Forums
ModeratorJoined Oct 1, '02From fall river, maCurrentlyOfflineReputation:13(100%)
6th Generation Celica
› Engine/Transmission/Maintenance
yes. but no.
clearances on shims and caps will be slightly diffrent between every set.
you will need to re-shim about every time.
clearances on shims and caps will be slightly diffrent between every set.
you will need to re-shim about every time.
Topic ID: 98962 • Post ID: 9993210
E153 in AT200 ST - 6G Celicas Forums
ModeratorJoined Oct 1, '02From fall river, maCurrentlyOfflineReputation:13(100%)
6th Generation Celica
› Engine/Transmission/Maintenance
nothing needed other than the correct mounts and brackets for the LH (Transmission) side and 205 shifter cables. 205 mount and bracket on the rear.
all the work for any "S" series engine (or 2gr for t...
all the work for any "S" series engine (or 2gr for t...
Topic ID: 98934 • Post ID: 9993123
GT-FOUR Hood - 6G Celicas Forums
ModeratorJoined Oct 1, '02From fall river, maCurrentlyOfflineReputation:13(100%)
6th Generation Celica
› Exterior Styling
the three vents that are on the GT-4 hood DO come painted from the factory. i have black ones. you MAY be able to get the proper color, i guess you'd have to try and find out....i tried but sh*t for b...
Topic ID: 9890 • Post ID: 9992906
Getting 300hp out of an st205 3sgte reliably? - 6G Celicas Forums
ModeratorJoined Oct 1, '02From fall river, maCurrentlyOfflineReputation:13(100%)
6th Generation Celica
› Forced Induction
3" intake and 3" exhaust, and just about 18psi should net you right about 300whp on a 3rd gen in a FWD setup, repeatable on a dynojet over and over.
been proven a few times here, and is pretty typical...
been proven a few times here, and is pretty typical...
Topic ID: 98644 • Post ID: 9990698
WTB: Gt-four brake caliper stickers - 6G Celicas Forums
ModeratorJoined Oct 1, '02From fall river, maCurrentlyOfflineReputation:13(100%)
6th Generation Celica
› Buying/Selling
aubry reed @ reed grafix on facebook.
her husband anthony reed is the creator of toyota enthusiats on facebook, cool people, and aubry can make about any kind/style of sticker you can think up.
her husband anthony reed is the creator of toyota enthusiats on facebook, cool people, and aubry can make about any kind/style of sticker you can think up.
Topic ID: 98396 • Post ID: 9988793
S54 5th Gear Swap - 6G Celicas Forums
ModeratorJoined Oct 1, '02From fall river, maCurrentlyOfflineReputation:13(100%)
6th Generation Celica
› Engine/Transmission/Maintenance
i posted a couple pics on facebook when i pulled mine out of my old tranz..i think if ya go thru dustins old thread, right click on the pics and follow the link to his photobucket you can prolly find ...
Topic ID: 98179 • Post ID: 9987007
MS3PRO EVO on 4th Gen 3sgte - 6G Celicas Forums
ModeratorJoined Oct 1, '02From fall river, maCurrentlyOfflineReputation:13(100%)
6th Generation Celica
› Forced Induction
good stuff man and decent #s for sure! tq looks to remain fairly steady thruout the run, which is awesome...the E85 runs are impressive! the S54 will hold the power, its the starts that kill the diff ...
Topic ID: 97949 • Post ID: 9985226
MS3PRO EVO on 4th Gen 3sgte - 6G Celicas Forums
ModeratorJoined Oct 1, '02From fall river, maCurrentlyOfflineReputation:13(100%)
6th Generation Celica
› Forced Induction
pretty sure walbro makes a e85 compatible replacement now, check out what all the mr2 guys are using. im sure aaron @ ats, eric @ hux racing or one of those guys will have a solid solution.
Topic ID: 97949 • Post ID: 9985219
MS3PRO EVO on 4th Gen 3sgte - 6G Celicas Forums
ModeratorJoined Oct 1, '02From fall river, maCurrentlyOfflineReputation:13(100%)
6th Generation Celica
› Forced Induction
lots of cool stuff here man! boost by gear can be a godsend in our fwd setups, especially as you ramp up the power.
a shame the board isnt as active with all the facebook stuff...guys could actually l...
a shame the board isnt as active with all the facebook stuff...guys could actually l...
Topic ID: 97949 • Post ID: 9985211
Speed Sensor - 6G Celicas Forums
ModeratorJoined Oct 1, '02From fall river, maCurrentlyOfflineReputation:13(100%)
6th Generation Celica
› Engine/Transmission/Maintenance
there is no fuse for the speed sensor.
Topic ID: 97886 • Post ID: 9984733
97+ supra turns on a gt4 bumper? - 6G Celicas Forums
ModeratorJoined Oct 1, '02From fall river, maCurrentlyOfflineReputation:13(100%)
6th Generation Celica
› Exterior Styling
lagos, they make clear turns for the gt-4...talk to mike (qatar11) he can hook you up...
Topic ID: 9753 • Post ID: 9981797
3rd Generation ST205 3SGTE Celica VS. 4th Generation ST215 3SGTE Caldi - 6G Celicas Forums
ModeratorJoined Oct 1, '02From fall river, maCurrentlyOfflineReputation:13(100%)
6th Generation Celica
› Forced Induction
3rd gen uses 20b, manifold and turbo are seperate peices.
4th gen uses a one peice mainfold/turbo, usually called ct15.
4th gen uses a one peice mainfold/turbo, usually called ct15.
Topic ID: 97084 • Post ID: 9977961
Turbo 5sfe, what do you guys do with the IAT sensor - 6G Celicas Forums
ModeratorJoined Oct 1, '02From fall river, maCurrentlyOfflineReputation:13(100%)
6th Generation Celica
› Forced Induction
it shouldnt see manifold temp. its intake temp, not manifold temp (2 diffrent sensors, the 5s dont have a MAT.)
it should be in the intake piping, before the turbo.
drill a hole in the intake piping, ...
it should be in the intake piping, before the turbo.
drill a hole in the intake piping, ...
Topic ID: 96960 • Post ID: 9977336
gt4 hoods group buys around 500$ - 6G Celicas Forums
ModeratorJoined Oct 1, '02From fall river, maCurrentlyOfflineReputation:13(100%)
6th Generation Celica
› Exterior Styling
you can go to your local toyo dealer give them the pt # for the hood, and they can get it for you for about 450 with NO shipping..why bother.
Topic ID: 9689 • Post ID: 9977086
celica st205 chargecooler system not working. - 6G Celicas Forums
ModeratorJoined Oct 1, '02From fall river, maCurrentlyOfflineReputation:13(100%)
6th Generation Celica
› Forced Induction
just a tap of the pedal should activate the system, it should stop the pump if the car idles for more tthan 30 seconds or somthing like that, i dont know the exact time, since mine has always been wir...
Topic ID: 96886 • Post ID: 9977009
celica st205 chargecooler system not working. - 6G Celicas Forums
ModeratorJoined Oct 1, '02From fall river, maCurrentlyOfflineReputation:13(100%)
6th Generation Celica
› Forced Induction
bridging the level sensor is a common thing, because even just a hair under a totally full intercooler will set code 54.
if you pull the LH side underplastic, you should be able to start the car, blip...
if you pull the LH side underplastic, you should be able to start the car, blip...
Topic ID: 96886 • Post ID: 9977007
Backyard garage painting - 6G Celicas Forums
ModeratorJoined Oct 1, '02From fall river, maCurrentlyOfflineReputation:13(100%)
Other
› Off Topic
build a booth as described above, wet the ground under and around the parts your painting, lots of cleaning of the panels to be painted, and lots of tacking with a tack cloth before and between coats ...
Topic ID: 96872 • Post ID: 9976889
Showing page 2 of 766 (15,303 total posts)