Forced Induction
3,483
Total Topics
25
Showing
1
Page 1 of 140
Topics in Forced Induction •
newest topics first
Bought a 96 GT with an incomplete 3SGTE swap and am having trouble determining the generation. Best way/place to find that information?...
About 6-8 months ago, I installed an EBC solenoid for the already-wired in Greddy ProFec B Spec II in my ST205 front clip conversion (JDM 3SGTE, 3rd G...
Looking into turbocharging my 7afe ST, performance parts are rare for this engine so I need to get creative with my build. I plan on running a B16 hea...
basicly, all the 3sgte stuff is a direct bolt in for the 202. the s54 is fine, been using it for over 10 years on my swap, as have many others.
shifte...
Can you go back to the stock one?
I had an issue with the catch can on one of my engines. If I vented it to atmosphere, it would smoke out the exhaust...
4th gen swaps are pretty common now. Having a complete harness is key. My 3rd gen swap was a breeze, no extension just a couple wires to solder and ...
Blitz k1-380v turbo...
It goes to a (bcs) boost control solinoid or sometimes called the VSV. It how the car limits the boost to lower pressures in first and second gear. ...
3" intake and 3" exhaust, and just about 18psi should net you right about 300whp on a 3rd gen in a FWD setup, repeatable on a dynojet over and over.
b...
Even if it fits and works then you have to worry about if you'll have enough oil capacity to keep the crank from starving, if you need an increased ca...
Consider your options, knowing how much gt4play sells them for and send me an offer via PM. Shipping to Canada will be 25 euro....
Following in the steps of everyone with their TMIC, I'm planning to lag my cooler and plan to use gold foiled tape.
http://designengineering.com/refle...
3rd gen runs on MAP only, there is no MAF. so open dump of BOF wont hurt anything.
put a fuel gauge on the rail to see if its a fuel issue.
i would a...
did you pull codes? Jump pins E1 and TE1 in the diagnostic box. Google Toyota OBD1 codes and it'll tell you exactly how to do it....
10,000??? Yeah that's a fair bit beyond my wallet
I wasn't actually thinking of going beyond 500bhp anyway but mines a rev 3 block so I was just a tou...
agreed about the piggyback. Piggyback on my Supra is fighting the stock ECU. Going standalone at the end of the year cuz eff that noise...
A lot of people use Doug Copeland of Wiregap and are very satisfied. His prices arent bad either.
http://www.wiregapinc.com/pricing/...
$2k for an E153 is a LOT. Generally, the MR2 gearbox is about $400, and the factory LSD is around $400 as well. Then you'll also need the LSD axle stu...
ct15b(sweet 16) in a ct26 housing? interesting......
As the title states, I have a 1996 OBD2 vehicle with a GEN3 swap, and I need to get it inspected. The shop tried plugging in to the OBD2 port, but it...
I remove and reflash some of the board components....
Can anyone help me figure out the part number for the serpentine belt ? On the gen 4 please iv been looking and I thought I found the right one but I ...
Do a search on intercooler pipe routing for a 3sgte. That is how I found how to route my piping. Most people take the pipe over the exhaust manifold...
Do I 100% need a turbo map sensor the one that is plugged into the intake ? I was told I can just go away with it and do it direct...
Get rid of the SAFC and get a standalone ECU. There are threads out there of people putting Megasquirt ECUs on that type of th build. The stock ECU ...